Auxiliary Telescope CSC Overview¶
Note
This is a template file that is associated with a template directory structure. This note will be deleted when the section is properly populated
This is the top-level description of what this section is about and what it includes. Below is a table of contents which is used to show the levels below this level. If there are no levels beneath this one, make sure the 2nd line is commented out
Warning
This page is under heavy development and is subject to change. Also may be inaccurate.
- Subsystem
- In this context, a subsystem is considered a logical grouping of CSCs.
This page provides a broad overview of the AuxTel CSCs. This page is meant for operators and developers who are looking for information on the software components that make up the Auxiliary Telescope.
- Purpose of page
- State who the audience is.
Overview¶
- Paragraph describing Auxiliary Telescope software
- only deals with CSCs
- Assume primary audience is operators
- Assume surface knowledge of middleware
The Auxiliary Telescope software stack uses a DDS based communication framework to command these components. The software consists of logical groupings of subsystems which are listed below. Then each individual CSC is listed below the summary of each subsystem.
Subsystems¶
- Full name of subsystem
- Summarize Purpose
- Summarize functionality
- List CSCs
ATTCS¶
| LSST the Docs: | https://ts-standardscripts.lsst.io |
|---|---|
| Name: | The Auxiliary Telescope Control System. |
The ATTCS’s purpose is to provide control to the Auxiliary Telescope.
Functionally, this is how the telescope’s tracking and motion control is commanded.
- ATDome
LSST the Docs: https://ts-atdome.lsst.io - Summarize functionality
The ATDome’s functionality is to provide a way to open and close the shutter of the dome.
- ATDomeTrajectory
LSST the Docs: https://ts-atdometrajectory.lsst.io The ATDomeTrajectory’s functionality is to command the dome to rotate.
- ATPtg
LSST the Docs: https://ts-atptg.lsst.io The pointing component’s functionality is to send azimuth and elevation commands to the Motion Control System.
- ATMCS
LSST the Docs: https://ts-atmcs.lsst.io The motion control system’s functionality is to command the positioning of the telescope.
ATCalSys¶
| LSST the Docs: | https://ts-standardscripts.lsst.io |
|---|---|
| Name: | The Auxiliary Telescope Calibration System. |
The ATCalSys’s purpose provides calibration control to the telescope.
This is how the telescope’s mirror and fine-tuning position is handled.
- ATMonochromator
LSST the Docs: https://ts-atmonochromator.lsst.io Provides control over narrow-band controllable wavelength output.
- ATHexapod
LSST the Docs: https://ts-athexapod.lsst.io Provides fine grained correction over telescope position.
- ATPneumatics
LSST the Docs: https://ts-atpneumatics.lsst.io Provides control over mirror pressure.
- FiberSpectrograph
LSST the Docs: https://ts-fiberspectrograph.lsst.io Measures wavelength of the various light sources.
- Electrometer
LSST the Docs: https://ts-electrometer.lsst.io Measures photons.
LATISS¶
| LSST the Docs: | https://ts-standardscripts.lsst.io |
|---|---|
| Name: | The Atmospheric Transmission and Slitless Spectrograph. |
LATISS’s purpose is to provide control to the camera.
- ATCamera
LSST the Docs: https://ts-atcamera.lsst.io Provides imaging.
- ATSpectrograph
LSST the Docs: https://ts-atspectrograph.lsst.io Measures spectra.